Skip to content
Rays little blog
Mostly about rebuilding an all but dead Yamaha RD250LC
  • Home page
  • About
  • Contact
  • LC-Project
  • Posts

Category: LC-Project

Second build – Final Photos

May 5, 2022 Raymond Briddock Leave a comment

Continue Reading →

Posted in: LC-Project, RD LC bikes

Second build -Day 7 : Final

May 3, 2022 Raymond Briddock Leave a comment

NOW we are ready for the final assembly, of all the new and bling parts.Firstly, replacement of the drain plug…

Continue Reading →

Posted in: LC-Project, RD LC bikes

Second build – Day 6

May 2, 2022 Raymond Briddock Leave a comment

All that’s left now is to fit the new bodywork… but wait. It seems a shame to spoil the whatsit…

Continue Reading →

Posted in: LC-Project, RD LC bikes

Second build – Day 5

April 25, 2022 Raymond Briddock Leave a comment

All that’s left now is some tidying up, and fitting the original donor bike bodywork to give it a ride…

Continue Reading →

Posted in: LC-Project, RD LC bikes

Second build – Day 4

April 23, 2022 Raymond Briddock Leave a comment

Another day pottering around doing bit by bit. Inspect, clean and paint RD250LC(4L2) Exhausts Paint all the exhausts with one…

Continue Reading →

Posted in: LC-Project, RD LC bikes

Second build – Day 3

April 20, 2022 Raymond Briddock Leave a comment

More pottering today before dismantling the rear wheel of my roadgoing LC to get the 250 sprockets and spacers for…

Continue Reading →

Posted in: LC-Project, RD LC bikes

Second build – Day 2

April 19, 2022 Raymond Briddock Leave a comment

Pottering and adding bits to the bike. Fit water pump and oil pump to fresh painted clutch cover Fit Newly…

Continue Reading →

Posted in: LC-Project, RD LC bikes

Second build – Day 1

April 15, 2022 Raymond Briddock Leave a comment

With all of the preparation done, (nearly), for the second build, powder coating, cleaning, repairing, it’s time to assemble the…

Continue Reading →

Posted in: LC-Project, RD LC bikes

Refurbishing the clutch cover.

April 10, 2022 Raymond Briddock Leave a comment

The clutch cover from the donor bike was so bad that I didn’t fit it to the bike for the…

Continue Reading →

Posted in: LC-Project, RD LC bikes

Stage 2 : Beautification

Raymond Briddock Leave a comment

The mechanical build was finished towards the end of 2021. I had repaired and replaced most items on the bike…

Continue Reading →

Posted in: LC-Project, RD LC bikes

Shakedown period : Clock whine.

December 17, 2021 Raymond Briddock Leave a comment

just over 100 miles into the running in period, and the weather turned a little colder, and my clocks began…

Continue Reading →

Posted in: LC-Project, RD LC bikes

Switchgear repair and assembly : LHS

December 12, 2021 Raymond Briddock Leave a comment

Inspection of the internals shows that mostly, the wiring is OK, if a little bit stiff and brittle with age.The…

Continue Reading →

Posted in: LC-Project, RD LC bikes

Switchgear cosmetics – LHS

November 14, 2021 Raymond Briddock Leave a comment

2 hours of careful masking and rubbing down with 240 grade wet’n’dry. A thorough degreasing with brake cleaner, followed by…

Continue Reading →

Posted in: LC-Project

Meanwhile : DIY Nickel Plating

September 9, 2021 Raymond Briddock Leave a comment

The wait for engine parts, and for a wheel to be sent off, skimmed, and returned, provides opportunity for another…

Continue Reading →

Posted in: LC-Project, RD LC bikes

Shakedown period : Rear brake drum

Raymond Briddock Leave a comment

Sometime in the years in which the bike had lain fallow, the rear brake drum had become oval.There are theories…

Continue Reading →

Posted in: LC-Project

Shakedown period : Clutch and gearchange

September 3, 2021 Raymond Briddock Leave a comment

The whole point of a “mechanical build” was to prove the chassis parts, and consolidate the reuse of so many…

Continue Reading →

Posted in: LC-Project

Finishing off : Clutch cables, chain, brakes and MOT

August 27, 2021 Raymond Briddock Leave a comment

With the carbs done, and the engine running to my satisfaction, it’s time to finish the job and get her…

Continue Reading →

Posted in: LC-Project

Carburettors : Drilling the brass balls

August 15, 2021 Raymond Briddock Leave a comment

After a disappointing first run of the bike, it is apparent that there is a problem with the bike running…

Continue Reading →

Posted in: LC-Project, RD LC bikes

Starting her up : Part 1

August 13, 2021 Raymond Briddock Leave a comment

I have run out of things to do without starting her up!I still need to check the shimming of the…

Continue Reading →

Posted in: LC-Project

Throttle Cable : Oil pump cable the wrong length

August 8, 2021 Raymond Briddock Leave a comment

Not wanting to pay £100 for a genuine Yamaha OEM throttle cable, I did as so many others do, bought…

Continue Reading →

Posted in: LC-Project, RD LC bikes

Post navigation

Page 1 of 4
1 2 … 4 Next →

Search

About This Site

Thoughts and musings from an early retired, self professed grumpy old man.

Interested in Motorcycles, Gaming, Science Fiction, and all manner of other stuff.

  • Email
Privacy Policy
Copyright © 2022 Rays little blog